學了一點金工,當作一個小興趣
借用鱗目的頭像
鋸好的樣子
一開始想做立體的耳朵,所以除了龍頭,還有一個耳朵
最後決定做平面的,頭上焊接一個圓環
簡單打磨,沒有電鍍~
有 13 位朋友喜欢这篇文章:peter860321, MorksAllen, 火柴龍, Immortaldragon, dragon1475632, 黑龙逐光, 小契, ken1882, shiningdracon, 沉默の龙, Jadescale, 龙游踏尘, Melayery
←目前頭像感謝安雅贈圖。
And I saw a new heaven and a new earth: for the first heaven and the first earth were passed away; and there was no more sea.
离线
@Dracostar3000 寫道: 雖然是龍的造型,特殊情況下拿來兼用手指虎也是很好的嘛=w=!!
照片中的白銀片是2.5cm*2.5cm ,要當手指虎大概要做5*5公分以上吧
好像是線切割 haku-indifferently
對,用線鋸
←目前頭像感謝安雅贈圖。
And I saw a new heaven and a new earth: for the first heaven and the first earth were passed away; and there was no more sea.
离线
@小契 寫道: 我的見識少...今天第一次知道金屬可以用線切果然線也是不能小看的
不是普通的線~
看起來像線的,是鋸絲~
https://jbs1937.com.tw/index_down.php?openCatID=4&CAhs=&II=18&CA=4&sele=shop
←目前頭像感謝安雅贈圖。
And I saw a new heaven and a new earth: for the first heaven and the first earth were passed away; and there was no more sea.
离线
@羽龍凌風 寫道: 很漂亮啊!比較好奇做掛飾會戳人嗎?
謝謝
其實我做好之後,不到24小時就送龍了,不知道他會不會覺得刺刺
如果覺得刺刺,999純銀很軟,用指甲刀磨一磨就好~
話說,背刺我原本想用磨的,後來無意間發現加熱到半熔化,白銀就因為內聚力變圓了,省下好多銼磨的時間
←目前頭像感謝安雅贈圖。
And I saw a new heaven and a new earth: for the first heaven and the first earth were passed away; and there was no more sea.
离线
[↑] @barufaruku 寫道: 話說要在上面刻劃圖案的話要怎麼操作啊,感覺手殘雕刻不好,衝壓沒有設備. 想自己做一個銀的徽標,圖案類似現在這個頭像這樣 …
職業的話用電腦雕刻機、氣動刀
職業雕刻設備
http://www.950.com.tw/tw/product.php?group=223&page=1&maxnum=15&SearchKey=
業餘的話可以用小電鑽,類似這個:
Octopus 章魚牌 254.660 套裝組 迷你刻模機 研磨機 刻磨機 電動雕刻機
這種手滑鑽到手指,也不會大傷害,相對安全,但是雕刻速度也偏慢~
圖片來源:https://24h.pchome.com.tw/prod/DEACA5-A90056Q8F
也可以圖案設計好後,找店家用專業的雕刻設備幫忙
最后修改: 龍爪翻書 (2021-03-30 06:18:54)
←目前頭像感謝安雅贈圖。
And I saw a new heaven and a new earth: for the first heaven and the first earth were passed away; and there was no more sea.
离线